+ Post New Thread
Page 1 of 2 1 2 LastLast
Threads 1 to 20 of 23

Forum: Electrical

What wire goes where?

  1. Sticky Thread Sticky: 1998 Harness Mod

    Circuit Number C1 (Red) This is going to take a while to put together. If anyone has the 99+ instructions and wants to post please do. This...

    Started by thomas.creation‎, 07-02-2012 06:38 PM
    • Replies: 3
    • Views: 4,730
    07-02-2012, 07:41 PM Go to last post
  1. Available vendors for LS to S2000 Harnesses?

    So I'm starting to make some good progress on my 5.3 Turbo LS swap into my AP1 street/drag car. (Solid 9" 4 link, cell, 28" slicks, 4.5" skinnies,...

    Started by Prokaw875‎, 07-21-2016 09:35 AM
    • Replies: 3
    • Views: 3,232
    10-28-2016, 10:03 PM Go to last post
  2. Cruise Control

    So first thread I made about this mysteriously disappeared? Does anybody have functioning cruise control with one of these swaps? I assumed it...

    Started by jonathan_ed3‎, 09-23-2016 05:49 PM
    • Replies: 7
    • Views: 2,032
    10-02-2016, 12:01 PM Go to last post
  3. Speedo + Eps not working

    I've got my car idling! Goes to the tuner on Tuesday to put a good map on it. Running an omex 710 series Ecu along side the honda, no Gm Ecu. I...

    Started by Carl Bourbon‎, 07-27-2014 01:37 PM
    2 Pages
    1 2
    • Replies: 10
    • Views: 4,863
    06-16-2016, 08:34 PM Go to last post
  4. Power Steering

    I can not get my power steering to work. I do not have the Honda ECU only the GM ECU. Somehow after going to the shop my power steering started to...

    Started by 1999s2k‎, 06-06-2013 02:36 AM
    • Replies: 7
    • Views: 4,141
    06-03-2016, 10:00 PM Go to last post
  5. 06+ DBW Inquire

    I apologize in advance if this has been addressed before, but I searched and could not find any answers. For those with with 06+ dbw s2000's, how...

    Started by toohai4yah‎, 03-09-2016 05:59 PM
    • Replies: 7
    • Views: 3,106
    06-03-2016, 07:53 AM Go to last post
  6. Does the SGI 5e's support of 16x ppm multiplication make gm or viper sensors a possib

    I noticed the SGI 5c speed sensor multiplier is no longer being produced and has been replaced by a new model. The previous model was able to...

    Started by imTehk‎, 04-30-2016 12:59 AM
    • Replies: 2
    • Views: 2,324
    05-04-2016, 10:34 PM Go to last post
  7. Wiring advice

    I bought the Import Muscle guide and I am still confused on the wiring. Part of this is due to having a standalone harness for my ls3. Id have a...

    Started by imTehk‎, 04-29-2016 09:16 PM
    • Replies: 0
    • Views: 2,045
    04-29-2016, 09:16 PM Go to last post
  8. PCM Location? Where Is Your Mounted? Advice

    alright guys, i'm in bed of help, who here has mounted there pcm inside the cabin on the driver side? if so, where and how did you do it? wiring is...

    Started by dean_c89‎, 09-09-2014 04:54 PM
    2 Pages
    1 2
    • Replies: 10
    • Views: 4,790
    04-11-2016, 06:34 PM Go to last post
  9. t56 reverse lockout solenoid

    on a 99-02 PCM, is it possible to enable the reverse lockout solenoid functionality via the PCM? The GM PCM uses the clutch position switch which...

    Started by jonathan_ed3‎, 11-10-2015 08:33 PM
    • Replies: 1
    • Views: 2,733
    11-10-2015, 10:13 PM Go to last post
  10. Tach not working

    I've got an issue where my Tach is not reading. I've got the single wire hooked up fine. I have all truck engine/harness/ecu and I'm wondering if...

    Started by recliner15‎, 11-07-2015 07:38 AM
    • Replies: 1
    • Views: 2,371
    11-09-2015, 08:55 PM Go to last post
  11. Dakota Digital SGI-5 issue

    I installed the IM speed sensor kit with the Tweak'd Performance harness and had an issue that stumped me for a couple weeks that I wanted to pass...

    Started by Drstrangelove‎, 07-04-2015 11:17 AM
    • Replies: 4
    • Views: 3,077
    08-07-2015, 02:23 PM Go to last post
  12. Wiring Theory

    I have my gauges (AFR/Oil Pressure/Water Temp/Shift Light/Ethanol Content) wired to a 600v/15amp bus/panel; single 12v connection to the drivers side...

    Started by herecomesboost‎, 02-19-2014 09:10 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 30
    • Views: 11,163
    07-09-2015, 09:37 PM Go to last post
  13. Merging GM and Honda evap systems?

    Has any one successfully used the GM PCM to control the honda evap system? I will figure it out, but I would love to hear from others about their...

    Started by Keith P‎, 05-05-2014 02:42 AM
    • Replies: 4
    • Views: 3,629
    06-30-2015, 11:07 PM Go to last post
  14. HELP how to wire the ls harness to S2K harness

    I need some real help on doing the wiring on the LS1 swap,, i have a motor from a 99 SS camaro, i have the full harness and ecu,, but i don't know...

    Started by NFR01‎, 10-28-2013 10:16 PM
    • Replies: 7
    • Views: 4,981
    04-17-2015, 01:38 PM Go to last post
  15. Gauging Interest - AEM Infinity harness - dbw

    I know most of you guys run an oem GM ecu, but we have done a few ls swapped cars with AEM infintiy and retained the DBW throttle, I wanted to gauge...

    Started by Wadzii‎, 01-28-2015 06:52 PM
    • Replies: 5
    • Views: 3,456
    04-09-2015, 04:12 AM Go to last post
  16. Which ECU to use?

    Hey, I'm going to be running HPTuners to run nitrous and tune. Which ECU do I need to run? Does it really matter which ECU I use if I'm going to...

    Started by ryguy2588‎, 11-04-2014 12:30 AM
    • Replies: 2
    • Views: 2,958
    11-13-2014, 11:36 PM Go to last post
  17. 5.3 swap questions

    I purchased a 5.3 aluminum block for my swap instead of an LS1 It came with the wiring harness and ECU Does anyone know what the differences are...

    Started by recliner15‎, 09-15-2014 11:17 AM
    • Replies: 5
    • Views: 3,365
    10-21-2014, 08:29 PM Go to last post
  18. Speed sensor

    I'm not sure if any of you follow us on our Facebook page and have seen this already. This might come in handy for some of your builds out there....

    Started by xyster‎, 04-25-2014 07:47 AM
    • Replies: 8
    • Views: 3,917
    04-29-2014, 10:23 PM Go to last post
  19. Idea for Import Muscle owners...prefab harnesses

    I used to have an LS1 powered FD RX7 and am planning to do an LS1 S2000 next (after my current lease runs up in about 1.5 years). The RX7 swap...

    Started by boostd92‎, 11-09-2012 12:39 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 9,666
    03-14-2013, 12:57 AM Go to last post
  20. What do I need to keep?

    I want to be able to use my stock gauge cluster, what all needs to be kept in my S2000 to do so? Does the ECU run any of this or is it seperate?

    Started by Ebush‎, 04-03-2012 01:34 PM
    2 Pages
    1 2
    • Replies: 18
    • Views: 8,004
    04-08-2012, 11:57 AM Go to last post

+ Post New Thread

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts